Envco – Environmental Equipment

The PPWS Console, Model 3115, is supplied in water and dust proof Pelican instrument case. The 3115 can be configured as a 25 or 40 bar (25 or 40 Mpa) platform with either the G4 or G2 specimen holder (for petioles and stems to ½” (125 mm), or blade leaves to 1” (254 mm) respectively. Choose either the standard 22 cu. ft. capacity or purchase the optional 33 cu. ft. capacity compressed gas bottle, for a small additional cost. The 3115 uses a quick-connect/disconnect, teflon hose with stainless steel braids, and an external Pressure Regulator, preset at the factory for the maximum operating pressure of 40 bar (4.0 MPa) or 25 bar (2.5 MPa).

The PPWS Console was thoroughly tested before shipment. When packed, it was in perfect working order. Unpack with care and remove all packing material. Follow the instructions carefully in order to assure long, trouble-free service.

CONSOLE SPECIFICATIONS
Weight: 26 lbs (11.8 kgs) (including tank)
Dimensions: 18.5 x 14.5 x 7 inches
Pressure Vessel: 1/2 liter (internal); stainless steel, 4 internal cam locks
Gauges: Test Gauge, 4.5 in, white face, 0-20 bar (300 psi) or 0-40 bar (600 psi), accurate to within 1/4 of 1% full scale. Source Tank test gauge, 1.5 in, white face (0-3000 psi), part of the 3074 Quick Connect pressure supply hose assembly.
Valves: Female, CGA 580 main valve on Compressed Gas Cylinder; Metering Valve to adjust the inflow pressurization rate for uniform measurements; Three-Way Pressure Control Valve to pressurize or to exhaust gas in the pressure vessel.
Connecting Hose: Stainless steel pressure hose with quick connect/disconnect at the PPW end and a male CGA 580 fitting on the compressed gas cylinder side.
Pressure Tank: Either 33 cu.ft. Compressed Gas Cylinder, 6.9” diameter x 15.8” length (shipped empty) or 22 cu.ft. Compressed Gas Cylinder, 5.25” diameter x 16.3” length (shipped empty)
Specimen Holder: Accepts either sealing sleeves or sealing grommets for leaves or stems using 3015G4 Specimen Holder, or use sealing plugs with the 3015G2 Specimen Holder for blade-type leaves . Has a stainless steel sealing knob and aluminum closing ring, stainless steel camlock with safety relief piston (to prevent build up in the pressure chamber unless the specimen holder is cam-locked in proper position).

Ordering Information
3115P40 – 40 BAR PLANT WATER STATUS CONSOLE – Please select from the different specimen holders and pressure in ordering your unit. G4 – Standard Specimen Holder for most plants, G2 – Broad Leaf plants and grains.
V22 – A tank that holds 22 cu ft. of compressed air ( size and weight of tank)
V33 - A tank that holds 33 cu ft. of compressed air (size and weight of tank)
EXAMPLE IS A 3115P40 that has a G4 Specimen Holder and 33 cu ft tank PLEASE ORDER 3115P40G4V33
3115P40G2VNI SAPS-II PWSC SYSTEM, 40 Bar, G2 Speciman Holder, CGA Air Tank - NOT INCLUDED
3115P40G2V22 SAPS-II PWSC SYSTEM, 40 Bar, G2 Speciman Holder, 22 cu.ft. CGA Air Tank
3115P40G2V33 SAPS-II PWSC SYSTEM, 40 Bar, G2 Speciman Holder, 33 cu.ft. CGA Air Tank
3115P40G4VNI SAPS-II PWSC SYSTEM, 40 Bar, G4 Speciman Holder, CGA Air Tank - NOT INCLUDED
3115P40G4V22 SAPS-II PWSC SYSTEM, 40 Bar, G4 Speciman Holder, 22 cu.ft. CGA Air Tank
3115P40G4V33 SAPS-II PWSC SYSTEM, 40 Bar, G4 Speciman Holder, 33 cu.ft. CGA Air Tank

Replacement & Accessory Parts for the 3115
0761G12 Valve, ball, 3-way, 6000 psi/413.8MPa
0761G13 Metering Flow Control Valve
0777L60 Valved Filler Hose, 60in/1.52m, ss braided hose, 3005 and 3115 models
0781P1500 Regulated Pressure Gauge,1500psi/103.5MPa, 1.5in/3.8cm,white
0781P3000 Source Tank Pressure Gauge, 3000psi/206.9MPa, 1.5in/3.8cm,white
0783P0600 Dual Scale (psi/bar), 0to600psi/0to40bar, 4.5in/11.4cm, floating needle, white
0783P0350 Dual Scale (psi/bar), 0to350psi/0to25bar, 4.5in/11.4cm, floating needle, white
3015G2 G2 Specimen Holder, for blade type leaves up to 1in/2.5cm wide
3015G2-001CR G2 Housing, specimen holder
3015G2-002 Compression ring, specimen holder, G2 only
3015G4 G4 Specimen Holder, for stems and leaves up to ½in/1.3cm diam
3015G4-001CR G4 Housing, specimen holder
3015G4-002 G4 Insert (helicoil), replacement, specimen holder
Z3015G4-003 G4 Closing Ring, specimen holder
Z3015G1-004 Piston, safety relief action, all specimen holders
Z3015G1-005 Retaining Collar, for piston, all specimen holders
Z3015G4-100 G4 Sealing Knob, specimen holder, G4 only
3071L60 Quick Connect Hose, regulated, 60in/1.52m, teflon ss braided hose only
3072V22 Compressed Gas Cylinder, 22 cuft/623.0 l
3072V33 Compressed Gas Cylinder, 33 cuft/934.6 l
M802X149 Buna N O-ring Seal, for G2/G4 specimen holders
M802X003 O-ring Seal, Piston safety relief, for G2/G4 specimen holders
MSM002-002 Spring, Piston safety relief, for G2/G4 specimen holders
MSL014-005 Roll Pin, stop, for G2/G4 specimen holders, 3/32in x 5/16in
Q0832CAQ05 Screws (4), flathead, 8-32x5/16”, G4 specimen holders
Q1024CAF10 Screws (3), socket head, 10-24 x 5/16”, stainless steel
MSL032 hex , Allen Wrench, G2 Specimen Holder
Z3015K1 Up-grade kit, Safety Relief Piston

Sealing Plugs, Sleeves, Grommets, and Support Washers
3017G2-005 G2 Sealing Plug, .094in/2.39cm wide, slot
3017G2-006 G2 Sealing Plug, .05in/0.13cm wide, slot
3018G4K1 G4 Stem Sleeve Sealing Kit, all sleeves and washers
3018G4K2 G4 Complete Sleeve Kit, 1 each of all sleeves
3018G4-000K1 G4 Sealing Sleeve, 5 PACK, 1/2in/1.27cm diam, blank
3018G4-001K1 G4 Sealing Sleeve, 5 PACK, 1/2in/1.27cm diam, 1/16in/0.159cm diam hole
3018G4-002K1 G4 Sealing Sleeve, 5 PACK, 1/2in/1.27cm diam, 1/8in/0.318cm diam hole
3018G4-003K1 G4 Sealing Sleeve, 5 PACK, 1/2in/1.27cm diam, 3/16in/0.478cm diam hole
3018G4-004K1 G4 Sealing Sleeve, 5 PACK, 1/2in/1.27cm diam, 1/4in/0.635cm diam hole
3018G4-005K1 G4 Sealing Sleeve Compression Holder, 5 PACK, 1/2in/1.27cm, saucer-type
3019G4-001K1 G4 Stem Grommet, 5 PACK, 1/16in/0.159cm diam hole
3019G4-002K1 G4 Stem Grommet, 5 PACK, 3/32in/0.24cm diam. hole
3019G4-003K1 G4 Stem Grommet, 5 PACK, 1/8in/0.318cm diam hole
3019G4-004K1 G4 Stem Grommet, 5 PACK, 3/16in/0.478cm diam hole
3019G4-005K1 G4 Leaf Grommet, 5 PACK, 1/16in/0.159cm wide X 1/4in/0.635cm ellipse
3019G4-006K1 G4 Leaf Grommet, 5 PACK, 1/8in/0.318cm wide X 1/2in/1.27cm ellipse
3019G4-007K1 G4 Leaf Grommet, 5 PACK, 1/8in/0.318cm wide X 1/2in/1.27cm arc
3019G4-008K1 G4 Leaf Grommet, 5 PACK, .05in/0.13cm wide X 1/2in/1.27cm slot
3019G4-009K1 G4 Stem Grommet, 5 PACK, blank
3019G4-010K1 G4 Stem Grommet, 5 PACK, 3/8in/0.95cm diam hole
3019G4-011K1 G4 Stem Grommet, 5 PACK, 1/2in/1.27cm diam hole
3019K1 G4 Stem Grommet Kit, 1 each all stem grommets and support washers
3019K2 G4 Leaf Grommet Kit, 1 each all leaf grommets and support washers
3019K3 G4 Complete Sleeve/Grommet Kit, all sleeves, grommets and washers
3020G4K1 G4 Brass Support Washer Kit, all washers for round holes
3020G4K2 G4 Brass Support Washer Kit, all washers for arcs and elipses
3020G4-001K1 G4 Brass Support Washer, 1/4” diam. hole, 5 PACK
3020G4-002K1 G4 Brass Support Washer, 1/16” wide X 1/2” slot, 5 PACK
3020G4-003K1 G4 Brass Support Washer, 1/8” wide X 1/2” slot, 5 PACK
3020G4-004K1 G4 Brass Support Washer, 3/8” diam. hole, 5 PACK
3020G4-005K1 G4 Brass Support Washer, 1/2” diam. hole, 5 PACK
3020G4-006K1 G4 Brass Support Washer, 9/64” diam. hole, 5 PACK
3021G2-000K1 G2 Brass Support Washer, blank, 5 PACK
3021G2-001K1 G2 Brass Support Washer, 1/16in/0.158cm slot, 5 PACK